KOnfigurasi EIGRP Filtering - Prefix List - Out

KOnfigurasi EIGRP Filtering - Prefix List - Out

May 09, 2017 Add Comment

Pertama kita mulai mengkonfigurasi IP addressnya

R1(config)#int lo0
R1(config-if)#ip add 1.1.1.1 255.255.255.255
R1(config)#int se0/0
R1(config-if)#no sh
R1(config-if)#ip add 12.12.12.1 255.255.255.0

R2(config)#int lo0
R2(config-if)#ip add 2.2.2.2 255.255.255.255
R2(config-if)#int s0/0
R2(config-if)#no sh
R2(config-if)#ip add 12.12.12.2 255.255.255.0
R2(config-if)#int f0/0
R2(config-if)#no sh
R2(config-if)#ip add 23.23.23.2 255.255.255.0
R2(config-if)#ex

R3(config)#int lo0
R3(config-if)#ip add 3.3.3.3 255.255.255.255
R3(config-if)#int fa0/0
R3(config-if)#no sh
R3(config-if)#ip add 23.23.23.3 255.255.255.0
R3(config-if)#ex

Kemudian kita konfigurasi routing eigrp

R1(config)#router eigrp 10
R1(config-router)#no au
R1(config-router)#net 1.1.1.1 0.0.0.0
R1(config-router)#net 12.12.12.0 0.0.0.0
R1(config-router)#ex

R2(config)#router eigrp 10
R2(config-router)#no au
R2(config-router)#net 12.12.12.0 0.0.0.0 
R2(config-router)#net 2.2.2.2 0.0.0.0
R2(config-router)#net 23.23.23.0 0.0.0.255

R3(config)#router eigrp 10
R3(config-router)#no au
R3(config-router)#net 3.3.3.3 0.0.0.0
R3(config-router)#net 23.23.23.0 0.0.0.0
R3(config-router)#ex

Selanjutnya kita konfigurasi interace loopback tambahan di router 3

R3(config)#int lo1
R3(config-if)#ip add 10.10.10.1 255.255.255.255

R3(config-if)#int lo2                         
R3(config-if)#ip add 10.10.10.5 255.255.255.252
R3(config-if)#int lo3                         
R3(config-if)#ip add 10.10.10.9 255.255.255.248   
R3(config-if)#int lo4
R3(config-if)#ip add 10.10.10.25 255.255.255.240  
R3(config-if)#ex

konfigurasi sumari di eigp 10 di router 3

R3(config)#router eigrp 10
R3(config-router)#net 0.0.0.0
R3(config-router)#ex

selanjutnya cek tabel routingnya di router 2

R2(config)#do sh ip ro
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

     1.0.0.0/32 is subnetted, 1 subnets
D       1.1.1.1 [90/409600] via 12.12.12.1, 00:31:10, FastEthernet0/0
     2.0.0.0/32 is subnetted, 1 subnets
C       2.2.2.2 is directly connected, Loopback0
     3.0.0.0/32 is subnetted, 1 subnets
D       3.3.3.3 [90/409600] via 23.23.23.3, 00:32:01, FastEthernet0/1
     23.0.0.0/24 is subnetted, 1 subnets
C       23.23.23.0 is directly connected, FastEthernet0/1
     10.0.0.0/8 is variably subnetted, 5 subnets, 5 masks
D       10.10.10.8/29 [90/409600] via 23.23.23.3, 00:06:46, FastEthernet0/1
D       10.10.11.0/24 [90/409600] via 23.23.23.3, 00:06:46, FastEthernet0/1
D       10.10.10.1/32 [90/409600] via 23.23.23.3, 00:06:46, FastEthernet0/1
D       10.10.10.4/30 [90/409600] via 23.23.23.3, 00:06:46, FastEthernet0/1
D       10.10.10.16/28 [90/409600] via 23.23.23.3, 00:06:48, FastEthernet0/1
     12.0.0.0/24 is subnetted, 1 subnets
C       12.12.12.0 is directly connected, FastEthernet0/0
R2(config)#

SElanjutnya lakukan konfigurasi Filtering - Prefix List - Out di router 3

R3(config)#ip prefix-list EIGRP_OUT seq 5 deny 10.10.10.0/24 ge 27 le 30
R3(config)#ip prefix-list EIGRP_OUT seq 10 permit 0.0.0.0/0 le 32
R3(config)#router eigrp 10
R3(config-router)#distribute-list prefix EIGRP_OUT out
R3(config-router)#ex

Selanjutnya cek tabel routing di router 2
R2(config)#do sh ip ro
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

     1.0.0.0/32 is subnetted, 1 subnets
D       1.1.1.1 [90/409600] via 12.12.12.1, 00:32:35, FastEthernet0/0
     2.0.0.0/32 is subnetted, 1 subnets
C       2.2.2.2 is directly connected, Loopback0
     3.0.0.0/32 is subnetted, 1 subnets
D       3.3.3.3 [90/409600] via 23.23.23.3, 00:33:27, FastEthernet0/1
     23.0.0.0/24 is subnetted, 1 subnets
C       23.23.23.0 is directly connected, FastEthernet0/1
     10.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
D       10.10.11.0/24 [90/409600] via 23.23.23.3, 00:08:11, FastEthernet0/1
D       10.10.10.1/32 [90/409600] via 23.23.23.3, 00:08:11, FastEthernet0/1
     12.0.0.0/24 is subnetted, 1 subnets
C       12.12.12.0 is directly connected, FastEthernet0/0
R2(config)#

EIGRP - Default Route - Static Route

EIGRP - Default Route - Static Route

May 09, 2017 Add Comment

Assalamualaikum wr wb

Alhamdulillah kita masih bisa sharing kembali tentuya di sinaubraeng 19, melanjutkan materi EIGRP yang sebelumnya kali ini kita akan membahas tentang cara Cara Konfigurasi EIGRP - Default Route - Summary, kali ini kita akan membahas tentang EIGRP - Default Route - Static Route.

Pertama kita mulai mengkonfigurasi IP addressnya

R1(config)#int lo0
R1(config-if)#ip add 1.1.1.1 255.255.255.255
R1(config)#int se0/0
R1(config-if)#no sh
R1(config-if)#ip add 12.12.12.1 255.255.255.0

R2(config)#int lo0
R2(config-if)#ip add 2.2.2.2 255.255.255.255
R2(config-if)#int s0/0
R2(config-if)#no sh
R2(config-if)#ip add 12.12.12.2 255.255.255.0
R2(config-if)#int f0/0
R2(config-if)#no sh
R2(config-if)#ip add 23.23.23.2 255.255.255.0
R2(config-if)#ex

R3(config)#int lo0
R3(config-if)#ip add 3.3.3.3 255.255.255.255
R3(config-if)#int fa0/0
R3(config-if)#no sh
R3(config-if)#ip add 23.23.23.3 255.255.255.0
R3(config-if)#ex

Kemudian kita konfigurasi routing eigrp

R1(config)#router eigrp 10
R1(config-router)#no au
R1(config-router)#net 1.1.1.1 0.0.0.0
R1(config-router)#net 12.12.12.0 0.0.0.0
R1(config-router)#ex

R2(config)#router eigrp 10
R2(config-router)#no au
R2(config-router)#net 12.12.12.0 0.0.0.0 
R2(config-router)#net 2.2.2.2 0.0.0.0
R2(config-router)#net 23.23.23.0 0.0.0.255

R3(config)#router eigrp 10
R3(config-router)#no au
R3(config-router)#net 3.3.3.3 0.0.0.0
R3(config-router)#net 23.23.23.0 0.0.0.0
R3(config-router)#ex

Selanjutnya kita konfigurasi interace loopback tambahan di router 3

R3(config)#int lo1
R3(config-if)#ip add 10.10.10.1 255.255.255.255

kemudian tambahkan defaut route pada router 3

R3(config)#ip route 0.0.0.0 0.0.0.0 Null 0

senjutnya konfigurasi redistribute static di router 3 routing eigrpnya

R3(config)#router eigrp 10
R3(config-router)#redistribute static

Selanjutnya kita cek di route R1 tabel routingnya

Selanjutnya kita coba lakukan ping

D*EX 0.0.0.0/0 [170/2195456] via 12.12.12.2, 00:00:13, Serial0/0
R1#ping 10.10.10.1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.10.10.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 4/27/92 ms
R1#

Cara Konfigurasi EIGRP - Default Route - Summary

Cara Konfigurasi EIGRP - Default Route - Summary

Superlab Cisco

May 08, 2017 Add Comment

Assalamualaikum wr wb

Alhamdulillah kita masih bisa sharing kembali tentuya di sinaubraeng 19, melanjutkan materi EIGRP yang sebelumnya kali ini kita akan membahas tentang cara

Pertama kita mulai mengkonfigurasi IP addressnya

R1(config)#int lo0
R1(config-if)#ip add 1.1.1.1 255.255.255.255
R1(config)#int se0/0
R1(config-if)#no sh
R1(config-if)#ip add 12.12.12.1 255.255.255.0

R2(config)#int lo0
R2(config-if)#ip add 2.2.2.2 255.255.255.255
R2(config-if)#int s0/0
R2(config-if)#no sh
R2(config-if)#ip add 12.12.12.2 255.255.255.0
R2(config-if)#int f0/0
R2(config-if)#no sh
R2(config-if)#ip add 23.23.23.2 255.255.255.0
R2(config-if)#ex

R3(config)#int lo0
R3(config-if)#ip add 3.3.3.3 255.255.255.255
R3(config-if)#int fa0/0
R3(config-if)#no sh
R3(config-if)#ip add 23.23.23.3 255.255.255.0
R3(config-if)#ex

Kemudian kita konfigurasi routing eigrp

R1(config)#router eigrp 10
R1(config-router)#no au
R1(config-router)#net 1.1.1.1 0.0.0.0
R1(config-router)#net 12.12.12.0 0.0.0.0
R1(config-router)#ex

R2(config)#router eigrp 10
R2(config-router)#no au
R2(config-router)#net 12.12.12.0 0.0.0.0 
R2(config-router)#net 2.2.2.2 0.0.0.0
R2(config-router)#net 23.23.23.0 0.0.0.255

R3(config)#router eigrp 10
R3(config-router)#no au
R3(config-router)#net 3.3.3.3 0.0.0.0
R3(config-router)#net 23.23.23.0 0.0.0.0
R3(config-router)#ex

Selanjutnya kita konfigurasi interace loopback tambahan di router 3

R3(config)#int lo1
R3(config-if)#ip add 10.10.10.1 255.255.255.255

Selanjutnya di router 3 kita lakukan konfigurasi  Default Route - Summary

R3(config-if)#int fa0/0
R3(config-if)#ip summary-address eigrp 10 0.0.0.0 0.0.0.0

Kemudian cek tabel routing di router 1

EIGRP - Redistribution RIP

EIGRP - Redistribution RIP

Superlab Cisco

May 08, 2017 Add Comment

Assalamualaikum wr wb

Alhamdulillah kita masih bisa bertemu sharing sharing tentunya di sinaubareng19 kali ini kita akan melanjutkan yang sebelumnya yaitu yang redistribute static, kali ini kita akan membahas tentang redistribute RIP, untuk topologi kita masih sama seprti yang sebelumnya yaitu seperti dibawah ini.

Pertama kita mulai mengkonfigurasi IP addressnya

R1(config)#int lo0
R1(config-if)#ip add 1.1.1.1 255.255.255.255
R1(config)#int se0/0
R1(config-if)#no sh
R1(config-if)#ip add 12.12.12.1 255.255.255.0

R2(config)#int lo0
R2(config-if)#ip add 2.2.2.2 255.255.255.255
R2(config-if)#int s0/0
R2(config-if)#no sh
R2(config-if)#ip add 12.12.12.2 255.255.255.0
R2(config-if)#int f0/0
R2(config-if)#no sh
R2(config-if)#ip add 23.23.23.2 255.255.255.0
R2(config-if)#ex

R3(config)#int lo0
R3(config-if)#ip add 3.3.3.3 255.255.255.255
R3(config-if)#int fa0/0
R3(config-if)#no sh
R3(config-if)#ip add 23.23.23.3 255.255.255.0
R3(config-if)#ex

Kemudian kita konfigurasi routing eigrp

R1(config)#router eigrp 10
R1(config-router)#no au
R1(config-router)#net 1.1.1.1 0.0.0.0
R1(config-router)#net 12.12.12.0 0.0.0.0
R1(config-router)#ex

R2(config)#router eigrp 10
R2(config-router)#no au
R2(config-router)#net 12.12.12.0 0.0.0.0 
R2(config-router)#net 2.2.2.2 0.0.0.0
R2(config-router)#net 23.23.23.0 0.0.0.255

R3(config)#router eigrp 10
R3(config-router)#no au
R3(config-router)#net 3.3.3.3 0.0.0.0
R3(config-router)#net 23.23.23.0 0.0.0.0
R3(config-router)#ex

Selanjutnya kita konfigurasi interace loopback tambahan di router 3

R3(config)#int lo1
R3(config-if)#ip add 10.10.10.1 255.255.255.255

Selanjutnya kita konfiugrasi Routing RIP di router 3, epatnya di network lo1

R3(config)#router rip
R3(config-router)#ve 2
R3(config-router)#net 10.10.10.1          
R3(config-router)#no au       
R3(config-router)#redistribute eigrp 10 metric 10
R3(config-router)#ex

Selanjutnya di Eigrpnya kita redistribute RIP.

R3(config)#router eigrp 10
R3(config-router)#redistribute rip metric 1 1 1 1 1
R3(config-router)#ex

Selanjutnya pada router 1 kitacek tabel route dan lakukan ping

R1(config)#do sh ip ro
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

     1.0.0.0/32 is subnetted, 1 subnets
C       1.1.1.1 is directly connected, Loopback0
     2.0.0.0/32 is subnetted, 1 subnets
D       2.2.2.2 [90/2297856] via 12.12.12.2, 03:31:38, Serial0/0
     3.0.0.0/32 is subnetted, 1 subnets
D       3.3.3.3 [90/2323456] via 12.12.12.2, 03:31:10, Serial0/0
     23.0.0.0/24 is subnetted, 1 subnets
D       23.23.23.0 [90/2195456] via 12.12.12.2, 03:31:52, Serial0/0
     10.0.0.0/32 is subnetted, 1 subnets
D EX    10.10.10.1 [170/2560537856] via 12.12.12.2, 00:00:05, Serial0/0
     12.0.0.0/24 is subnetted, 1 subnets
C       12.12.12.0 is directly connected, Serial0/0
R1(config)#

 Selanjutnya lakukan ping

R1(config)#do ping 10.10.10.1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.10.10.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 8/16/24 ms
R1(config)#

EIGRP - Redistribution Static

EIGRP - Redistribution Static

Superlab Cisco

May 08, 2017 Add Comment

 Assalamualaikum wr wb

Alhamdulillah kita masih bisa berjumpa lagi tentunya di sinau bareng19 kali ini kita akan melanjutkan yang kemrin yaitu tentang EIGRP - Redistribution Connected dan sekarang kita akan membahas tentang

Kemudian kita mulai mengkonfigurasi IP addressnya

R1(config)#int lo0
R1(config-if)#ip add 1.1.1.1 255.255.255.255
R1(config)#int se0/0
R1(config-if)#no sh
R1(config-if)#ip add 12.12.12.1 255.255.255.0

R2(config)#int lo0
R2(config-if)#ip add 2.2.2.2 255.255.255.255
R2(config-if)#int s0/0
R2(config-if)#no sh
R2(config-if)#ip add 12.12.12.2 255.255.255.0
R2(config-if)#int f0/0
R2(config-if)#no sh
R2(config-if)#ip add 23.23.23.2 255.255.255.0
R2(config-if)#ex

R3(config)#int lo0
R3(config-if)#ip add 3.3.3.3 255.255.255.255
R3(config-if)#int fa0/0
R3(config-if)#no sh
R3(config-if)#ip add 23.23.23.3 255.255.255.0
R3(config-if)#ex

Kemudian kita konfigurasi routing eigrp

R1(config)#router eigrp 10
R1(config-router)#no au
R1(config-router)#net 1.1.1.1 0.0.0.0
R1(config-router)#net 12.12.12.0 0.0.0.0
R1(config-router)#ex

R2(config)#router eigrp 10
R2(config-router)#no au
R2(config-router)#net 12.12.12.0 0.0.0.0 
R2(config-router)#net 2.2.2.2 0.0.0.0
R2(config-router)#net 23.23.23.0 0.0.0.255

R3(config)#router eigrp 10
R3(config-router)#no au
R3(config-router)#net 3.3.3.3 0.0.0.0
R3(config-router)#net 23.23.23.0 0.0.0.0
R3(config-router)#ex

Selanjutnya kita konfigurasi interace loopback tambahan di router 3

R3(config)#int lo1
R3(config-if)#ip add 10.10.10.1 255.255.255.255

Selanjutnya konfigurasi Static route di router 2 ke lo1 router 3

R2(config)#ip route 10.10.10.1 255.255.255.255 fa0/0

Kemudian lakukan redistribute static di router 2

R2(config)#router eigrp 10
R2(config-router)#redistribute static

Selanjutnya kita cekkembali tabel routingnya

R1(config)#do sh ip ro
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

     1.0.0.0/32 is subnetted, 1 subnets
C       1.1.1.1 is directly connected, Loopback0
     2.0.0.0/32 is subnetted, 1 subnets
D       2.2.2.2 [90/2297856] via 12.12.12.2, 02:49:12, Serial0/0
     3.0.0.0/32 is subnetted, 1 subnets
D       3.3.3.3 [90/2323456] via 12.12.12.2, 02:48:44, Serial0/0
     23.0.0.0/24 is subnetted, 1 subnets
D       23.23.23.0 [90/2195456] via 12.12.12.2, 02:49:27, Serial0/0
     10.0.0.0/32 is subnetted, 1 subnets
D EX    10.10.10.1 [170/2195456] via 12.12.12.2, 00:00:22, Serial0/0
     12.0.0.0/24 is subnetted, 1 subnets
C       12.12.12.0 is directly connected, Serial0/0
R1(config)#

EIGRP - Redistribution Connected

EIGRP - Redistribution Connected

May 08, 2017 Add Comment

Assalamualaikum wr wb

Alhamdulillah kita masih diberikan kesempatan untuk Sharing bersama lagi, melanjtkan materi yang kemarin yaitu tentang Konfigurasi EIGRP - Default Route - Summary Address sekarang kita akan menkonfigurasi EIGRP - Redistribution Connected. sepertibiasa kita mulai dari membuat topologi terlebih dahulu. buatlah seperti dibawwah ini.

Kemudian kita mulai mengkonfigurasi IP addressnya

R1(config)#int lo0
R1(config-if)#ip add 1.1.1.1 255.255.255.255
R1(config)#int se0/0
R1(config-if)#no sh
R1(config-if)#ip add 12.12.12.1 255.255.255.0

R2(config)#int lo0
R2(config-if)#ip add 2.2.2.2 255.255.255.255
R2(config-if)#int s0/0
R2(config-if)#no sh
R2(config-if)#ip add 12.12.12.2 255.255.255.0
R2(config-if)#int f0/0
R2(config-if)#no sh
R2(config-if)#ip add 23.23.23.2 255.255.255.0
R2(config-if)#ex

R3(config)#int lo0
R3(config-if)#ip add 3.3.3.3 255.255.255.255
R3(config-if)#int fa0/0
R3(config-if)#no sh
R3(config-if)#ip add 23.23.23.3 255.255.255.0
R3(config-if)#ex

Kemudian kita konfigurasi routing eigrp

R1(config)#router eigrp 10
R1(config-router)#no au
R1(config-router)#net 1.1.1.1 0.0.0.0
R1(config-router)#net 12.12.12.0 0.0.0.0
R1(config-router)#ex

R2(config)#router eigrp 10
R2(config-router)#no au
R2(config-router)#net 12.12.12.0 0.0.0.0 
R2(config-router)#net 2.2.2.2 0.0.0.0
R2(config-router)#net 23.23.23.0 0.0.0.255

R3(config)#router eigrp 10
R3(config-router)#no au
R3(config-router)#net 3.3.3.3 0.0.0.0
R3(config-router)#net 23.23.23.0 0.0.0.0
R3(config-router)#ex

Selanjutnya kita konfigurasi interace loopback tambahan di router 3

R3(config)#int lo1
R3(config-if)#ip add 10.10.10.1 255.255.255.255
R3(config-if)#int lo2                         
R3(config-if)#ip add 10.10.10.2 255.255.255.255
R3(config-if)#int lo3                         
R3(config-if)#ip add 10.10.10.3 255.255.255.255

Kemudian lakukan konfigurasi Redistribute connected

R3(config)#router eigrp 10
R3(config-router)#redistribute connected

kemdian kita cek tabel route nya di router 1

kemudian kita coba ping

R1(config)#do ping 10.10.10.2

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.10.10.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 4/10/20 ms
R1(config)#

Konfigurasi EIGRP - Default Route - Summary Address

Konfigurasi EIGRP - Default Route - Summary Address

Superlab Cisco

May 07, 2017 Add Comment

Assalamualaikum wr wb

Alhamdulillah kita masih diberikan kesempatan untuk Sharing bersama lagi, melanjtkan materi yang kemarin yaitu tentangKonfigurasi EIGRP - Equal Load Balancing  tapi sekaran gkita akan membahas yaiu Konfigurasi EIGRP - Default Route - Summary Address. buatlah topologi seperti dibawah ini.

Pertama kita tambahkan IP address di masing masing interface router.

R1(config)#int lo0
R1(config-if)#ip add 1.1.1.1 255.255.255.255
R1(config)#int se0/0
R1(config-if)#no sh
R1(config-if)#ip add 12.12.12.1 255.255.255.0

R2(config)#int lo0
R2(config-if)#ip add 2.2.2.2 255.255.255.255
R2(config-if)#int s0/0
R2(config-if)#no sh
R2(config-if)#ip add 12.12.12.2 255.255.255.0
R2(config-if)#int f0/0
R2(config-if)#no sh
R2(config-if)#ip add 23.23.23.2 255.255.255.0
R2(config-if)#ex

R3(config)#int lo0
R3(config-if)#ip add 3.3.3.3 255.255.255.255
R3(config-if)#int fa0/0
R3(config-if)#no sh
R3(config-if)#ip add 23.23.23.3 255.255.255.0
R3(config-if)#ex

Kemudian kita konfigurasi routing eigrp

R1(config)#router eigrp 10
R1(config-router)#no au
R1(config-router)#net 1.1.1.1 0.0.0.0
R1(config-router)#net 12.12.12.0 0.0.0.0
R1(config-router)#ex

R2(config)#router eigrp 10
R2(config-router)#no au
R2(config-router)#net 12.12.12.0 0.0.0.0 
R2(config-router)#net 2.2.2.2 0.0.0.0
R2(config-router)#net 23.23.23.0 0.0.0.255

R3(config)#router eigrp 10
R3(config-router)#no au
R3(config-router)#net 3.3.3.3 0.0.0.0
R3(config-router)#net 23.23.23.0 0.0.0.0
R3(config-router)#ex

Selanjutnya kita konfigurasi interace loopback tambahan di router 3

R3(config)#int lo1
R3(config-if)#ip add 10.10.10.1 255.255.255.255
R3(config-if)#int lo2                         
R3(config-if)#ip add 10.10.10.2 255.255.255.255
R3(config-if)#int lo3                         
R3(config-if)#ip add 10.10.10.3 255.255.255.255

Selanjutnya masih di router 3 tepatnya di interface f0/0, kita konfigurasi sumary address eigrp.

R3(config)#int fa0/0
R3(config-if)#ip summary-address eigrp 10 0.0.0.0 0.0.0.0  
R3(config-if)#ex

Selanjutnya kita cek tabel routing di router 1

R1(config)#do sh ip ro
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route

Gateway of last resort is 12.12.12.2 to network 0.0.0.0

     1.0.0.0/32 is subnetted, 1 subnets
C       1.1.1.1 is directly connected, Loopback0
     2.0.0.0/32 is subnetted, 1 subnets
D       2.2.2.2 [90/2297856] via 12.12.12.2, 00:02:46, Serial0/0
     23.0.0.0/24 is subnetted, 1 subnets
D       23.23.23.0 [90/2195456] via 12.12.12.2, 00:00:57, Serial0/0
     12.0.0.0/24 is subnetted, 1 subnets
C       12.12.12.0 is directly connected, Serial0/0
D*   0.0.0.0/0 [90/2323456] via 12.12.12.2, 00:00:20, Serial0/0
R1(config)#

Selanjutnya kita coba ping kesatu sama lain.

R1(config)#do ping 10.10.10.2

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.10.10.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 4/17/44 ms
R1(config)#

Konfigurasi EIGRP - Equal Load Balancing

Konfigurasi EIGRP - Equal Load Balancing

May 04, 2017 Add Comment

Alhamdulillah kita masih bisa sharing bareng lagi tentunya di sinaubareng19,
sekarang kita akan melakukan konfigurasi EIGRP - Equal Load
Balancing,antinya setiap router memiliki 2 jalur untuk sampai ke paketnya,
pertama kita buat topologi seperti dibawah ini

Konfigurasi IP addressnya terlebih dahulu
R1(config)#int lo0
R1(config-if)#ip add 1.1.1.1 255.255.255.255
R1(config-if)#int e0/0
R1(config-if)#no sh
R1(config-if)#ip add 12.12.12.1 255.255.255.0
R1(config-if)#int e0/1
R1(config-if)#no sh
R1(config-if)#ip add 14.14.14.1 255.255.255.0
R1(config-if)#ex

R2(config)#int lo0
R2(config-if)#ip add 2.2.2.2 255.255.255.255
R2(config-if)#int e0/0
R2(config-if)#no sh
R2(config-if)#ip add 12.12.12.2 255.255.255.0
R2(config-if)#int e0/1
R2(config-if)#no sh
R2(config-if)#ip add 23.23.23.2 255.255.255.0
R2(config-if)#ex
 
R3(config)#int lo0
R3(config-if)#ip add 3.3.3.3 255.255.255.255
R3(config-if)#int e0/0
R3(config-if)#no sh
R3(config-if)#ip add 23.23.23.3 255.255.255.0
R3(config-if)#int e0/1
R3(config-if)#no sh
R3(config-if)#ip add 34.34.34.3 255.255.255.0
R3(config-if)#ex
R4(config)#int lo0
R4(config-if)#ip add 4.4.4.4 255.255.255.255
R4(config-if)#int e0/0
R4(config-if)#no sh
R4(config-if)#ip add 14.14.14.4 255.255.255.0
R4(config-if)#int e0/1
R4(config-if)#no sh
R4(config-if)#ip add 34.34.34.4 255.255.255.0
R4(config-if)#ex

Selanjutnya konfiguasi routing eigrp
R1(config)#router eigrp 10
R1(config-router)#no au
R1(config-router)#net 0.0.0.0
R2(config)#router eigrp 10
R2(config-router)#no au
R2(config-router)#net 0.0.0.0
R3(config)#router eigrp 10
R3(config-router)#net 0.0.0.0
R3(config)#router eigrp 10
R3(config-router)#no au
R3(config-router)#ex
R4(config)#router eigrp 10
R4(config-router)#net 0.0.0.0
R4(config-router)#no au

Kemudian cek tabel routingnya