Superlab Cisco #1

Assalamualaikum wr.wb


Alhamdulillah saya diberi kesempatan untuk membagikan ilmu lagi kali ini kita mencoba sesuatu yang baru  yaitu Superlab Cisco #1 hari ini semangatkan? harus semangat ok!!,ini masih belum selesai masih banyak lagi yang mau saya bagikan, cukup basa basinya sekarang langsung saja berikut topologinya

Materi Lab

• VLAN
• Trunking
• DHCP Server
• EIGRP
• RIPv2
• OSPF
• DNS
• Redistribute

Tujuan Lab

Menghubungkan semua PC agar dapat mengakses Server yang ada di sebelah kiri, untuk menghubungkannya Router menggunakan EIGRP, RIPv2, OSPF yang saling diredistribute, salah satu Switch Layer 3 MLS juga menggunakan EIGRP untuk Routing protocolnya agar terhubung dengan jaringan lainnya dalam topologi tersebut.

PC akan diberikan alamat IP secara dinamis oleh DHCP Server, yang menjadi DHCP Server adalah Router dan MLS, setiap satu switch juga dipisahkan dengan VLAN.

Oke kita siapkan tenaga dan pikiran dan mulai konfigurasi, pertama kita akan konfigurasi di daerah dibawah ini terlebih dahulu

kita konfigurasi switchnya terlebih dahulu untuk pembuatan vlan dan trunking interface yang mengarah ke router.knp kok swithnya di setting?supaya hasil akhirnya tercapai yaitu pc atau lapto bisa saling komunikasi dengan ping

Switch(config)#hostname IDN-Switch2

IDN-Switch2(config)#vlan 10

IDN-Switch2(config-vlan)#name IDN-Vlan10

IDN-Switch2(config-vlan)#ex

IDN-Switch2(config)#vlan 20

IDN-Switch2(config-vlan)#name IDN-Vlan20

IDN-Switch2(config-vlan)#ex

IDN-Switch2(config)#interface fa0/1

IDN-Switch2(config-if)#switchport mode trunk

IDN-Switch2(config-if)#int fa0/2

IDN-Switch2(config-if)#switchport mode access

IDN-Switch2(config-if)#switchport access vlan 10

IDN-Switch2(config-if)#int f0/3

IDN-Switch2(config-if)#switchport mode access

IDN-Switch2(config-if)#switchport access vlan 10

IDN-Switch2(config-if)#int f0/4

IDN-Switch2(config-if)#switchport mode access

IDN-Switch2(config-if)#switchport access vlan 20

IDN-Switch2(config-if)#int f0/5

IDN-Switch2(config-if)#switchport mode access

IDN-Switch2(config-if)#switchport access vlan 20

IDN-Switch2(config-if)#ex

IDN-Switch2(config)#ex

kemudian kita lihat

IDN-Switch2#show vlan

 dan hasilnya

selanjutnya kita mengkonfigurasinya

IDN-R1(config)#int f0/0

IDN-R1(config-if)#no sh

IDN-R1(config-if)#ip addr 11.11.11.1 255.255.255.0

IDN-R1(config-if)#int serial2/0

IDN-R1(config-if)#no sh

IDN-R1(config-if)#no shutdown

%LINK-5-CHANGED: Interface Serial2/0, changed state to down

IDN-R1(config-if)#c

IDN-R1(config-if)#cl

IDN-R1(config-if)#clock r

IDN-R1(config-if)#clock rate 56000

This command applies only to DCE interfaces

IDN-R1(config-if)#ip addr 12.12.12.1 255.255.255.0

IDN-R1(config-if)#int fa1/0

IDN-R1(config-if)#no sh

IDN-R1(config-if)#

%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up

IDN-R1(config-if)#int fa1/0.10

IDN-R1(config-subif)#

%LINK-5-CHANGED: Interface FastEthernet1/0.10, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0.10, changed state to up

IDN-R1(config-subif)#en

IDN-R1(config-subif)#encapsulation d

IDN-R1(config-subif)#encapsulation dot1Q 10

IDN-R1(config-subif)#ip addr 10.10.10.1 255.255.255.0

IDN-R1(config-subif)#int fa1/0.20

IDN-R1(config-subif)#

%LINK-5-CHANGED: Interface FastEthernet1/0.20, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0.20, changed state to up

IDN-R1(config-subif)#en

IDN-R1(config-subif)#encapsulation d

IDN-R1(config-subif)#encapsulation dot1Q 20

IDN-R1(config-subif)#ip addr 20.20.20.1 255.255.255.0

IDN-R1(config-subif)#ex

IDN-R1(config)#do sh ip int br

Interface IP-Address OK? Method Status Protocol

FastEthernet0/0 11.11.11.1 YES manual up up

FastEthernet1/0 unassigned YES unset up up

FastEthernet1/0.10 10.10.10.1 YES manual up up

FastEthernet1/0.20 20.20.20.1 YES manual up up

Serial2/0 12.12.12.1 YES manual down down

Serial3/0 unassigned YES unset administratively down down

FastEthernet4/0 unassigned YES unset administratively down down

FastEthernet5/0 unassigned YES unset administratively down down

FastEthernet6/0 unassigned YES unset administratively down down

IDN-R1(config)#ro

IDN-R1(config)#router o

IDN-R1(config)#router ospf 10

IDN-R1(config-router)#net

IDN-R1(config-router)#networ

IDN-R1(config-router)#network 11.11.11.0 0.0.0.255 area 0

IDN-R1(config-router)#net 10.10.10.0 0.0.0.255 area 0

IDN-R1(config-router)#net 20.20.20.0 0.0.0.255 area 0

IDN-R1(config-router)#net 12.12.12.0 0.0.0.255 area 0

IDN-R1(config-router)#ex

 

Switch(config)#hostname IDN-SW1

IDN-SW1(config)#hostname IDN-SW3

IDN-SW3(config)#vlan 30

IDN-SW3(config-vlan)#na

IDN-SW3(config-vlan)#name Vlan-30

IDN-SW3(config-vlan)#ex

IDN-SW3(config)#vlan 40

IDN-SW3(config-vlan)#na

IDN-SW3(config-vlan)#name Vlan40

IDN-SW3(config-vlan)#ex

IDN-SW3(config)#int fa0/2

IDN-SW3(config-if)#sw

IDN-SW3(config-if)#switchport m

IDN-SW3(config-if)#switchport mode a

IDN-SW3(config-if)#switchport mode access

IDN-SW3(config-if)#sw

IDN-SW3(config-if)#switchport a

IDN-SW3(config-if)#switchport access v

IDN-SW3(config-if)#switchport access vlan 30

IDN-SW3(config-if)#int fa0/3

IDN-SW3(config-if)#sw

IDN-SW3(config-if)#switchport m

IDN-SW3(config-if)#switchport mode a

IDN-SW3(config-if)#switchport mode access

IDN-SW3(config-if)#sw

IDN-SW3(config-if)#switchport a

IDN-SW3(config-if)#switchport access v

IDN-SW3(config-if)#switchport access vlan 30

IDN-SW3(config-if)#ex

IDN-SW3(config)#int fa0/4

IDN-SW3(config-if)#sw

IDN-SW3(config-if)#switchport m

IDN-SW3(config-if)#switchport mode a

IDN-SW3(config-if)#switchport mode access

IDN-SW3(config-if)#sw

IDN-SW3(config-if)#switchport a

IDN-SW3(config-if)#switchport access v

IDN-SW3(config-if)#switchport a

IDN-SW3(config-if)#switchport access v

IDN-SW3(config-if)#switchport access vlan 40

IDN-SW3(config-if)#int fa0/5

IDN-SW3(config-if)#sw

IDN-SW3(config-if)#switchport a

IDN-SW3(config-if)#switchport m

IDN-SW3(config-if)#switchport mode

% Incomplete command.

IDN-SW3(config-if)#switchport mode a

IDN-SW3(config-if)#switchport mode access

IDN-SW3(config-if)#sw

IDN-SW3(config-if)#switchport a

IDN-SW3(config-if)#switchport access v

IDN-SW3(config-if)#switchport access vlan 40

IDN-SW3(config-if)#ex

IDN-SW3(config)#int fa

IDN-SW3(config)#int fastEthernet 0/1

IDN-SW3(config-if)#sw

IDN-SW3(config-if)#switchport m

IDN-SW3(config-if)#switchport mode t

IDN-SW3(config-if)#switchport mode trunk

IDN-SW3(config-if)#ex

IDN-SW3(config)#

 

Router>en

Router#conf t

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#int seria2/0

Router(config-if)#no sh

Router(config-if)#

%LINK-5-CHANGED: Interface Serial2/0, changed state to up

Router(config-if)#cl

Router(config-if)#clock r

Router(config-if)#clock rate 56000

Router(config-if)#

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up

Router(config-if)#ip addr 12.12.12.2 255.255.255.0

Router(config-if)#int serial3/0

Router(config-if)#no sh

%LINK-5-CHANGED: Interface Serial3/0, changed state to down

Router(config-if)#cl

Router(config-if)#clock r

Router(config-if)#clock rate 56000

This command applies only to DCE interfaces

Router(config-if)#ip addr 23.23.23.2 255.255.255.0

Router(config-if)#ro

Router(config-if)#rou

Router(config-if)#ex

Router(config)#ro

Router(config)#router o

Router(config)#router ospf 10

Router(config-router)#net 12.12.12.0 0.0.0.255

% Incomplete command.

Router(config-router)#net 12.12.12.0 0.0.0.255 area 0

Router(config-router)#net 12.12.12.0 0.0.0.255 area 0

00:15:45: %OSPF-5-ADJCHG: Process 10, Nbr 20.20.20.1 on Serial2/0 from LOADING to FULL, Loading Done

Router(config-router)#red

Router(config-router)#redistribute r

Router(config-router)#redistribute rip s

Router(config-router)#redistribute rip subnets

Router(config-router)#ex

Router(config)#rou

Router(config)#router r

Router(config)#router rip

Router(config-router)#ver2

^

% Invalid input detected at '^' marker.

Router(config-router)#ver 2

Router(config-router)#ner 23.23.23.0

^

% Invalid input detected at '^' marker.

Router(config-router)#net

Router(config-router)#network 23.23.23.0

Router(config-router)#re

Router(config-router)#redistribute o

Router(config-router)#redistribute ospf 10 m

Router(config-router)#redistribute ospf 10 me

Router(config-router)#redistribute ospf 10 metric 1

Router(config-router)#ex

Router(config)#

 

Router>en

Router#conf t

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#int fa0/0

Router(config-if)#no sh

Router(config-if)#

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

Router(config-if)#ip addr 34.34.34.3 255.255.255.0

Router(config-if)#int fa1/0

Router(config-if)#no sh

Router(config-if)#

%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up

Router(config-if)#ip addr 31.31.31.1 255.255.255.0

Router(config-if)#int seria2/0

Router(config-if)#no sh

Router(config-if)#

%LINK-5-CHANGED: Interface Serial2/0, changed state to up

Router(config-if)#cl

Router(config-if)#clock r

Router(config-if)#clock rate 5

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up

6

^

% Invalid input detected at '^' marker.

Router(config-if)#clo

Router(config-if)#clock r

Router(config-if)#clock rate 56000

Router(config-if)#ip addr 23.23.23.3

% Incomplete command.

Router(config-if)#ip addr 23.23.23.3 255.255.255.0

Router(config-if)#ro

Router(config-if)#rou

Router(config-if)#ex

Router(config)#ro

Router(config)#router r

Router(config)#router rip

Router(config-router)#ver 2

Router(config-router)#net 23.23.23.0

Router(config-router)#red

Router(config-router)#redistribute ei

Router(config-router)#redistribute eigrp m

Router(config-router)#redistribute eigrp 10

Router(config-router)#redistribute eigrp 10 me

Router(config-router)#redistribute eigrp 10 metric 1

Router(config-router)#ex

Router(config)#ro

Router(config)#router ei

Router(config)#router eigrp 10

Router(config-router)#net 34.34.34.0

Router(config-router)#redi

Router(config-router)#redistribute r

Router(config-router)#redistribute rip m

Router(config-router)#redistribute rip metric 1 1 1 1 1

Router(config-router)#ex

Router(config)#

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

%DUAL-5-NBRCHANGE: IP-EIGRP 10: Neighbor 34.34.34.4 (FastEthernet0/0) is up: new adjacency

Router#conf terminal

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#int f0/0

Router(config-if)#no sh

Router(config-if)#no shutdown

Router(config-if)#

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

Router(config-if)#ip addr 34.34.34.4 255.255.255.0

Router(config-if)#int fa1/0

Router(config-if)#no sh

Router(config-if)#

%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up

Router(config-if)#ip addr 44.44.44.1 255.255.255.0

Router(config-if)#int fa6/0

Router(config-if)#no sh

Router(config-if)#

%LINK-5-CHANGED: Interface FastEthernet6/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet6/0, changed state to up

Router(config-if)#int fa6/0.30

Router(config-subif)#

%LINK-5-CHANGED: Interface FastEthernet6/0.30, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet6/0.30, changed state to up

Router(config-subif)#en

Router(config-subif)#encapsulation d

Router(config-subif)#encapsulation dot1Q 30

Router(config-subif)#ip addr 30.30.30.0 255.255.255.0

Bad mask /24 for address 30.30.30.0

Router(config-subif)#ip addr 30.30.30.1 255.255.255.0

Router(config-subif)#int fa6/0.40

Router(config-subif)#

%LINK-5-CHANGED: Interface FastEthernet6/0.40, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet6/0.40, changed state to up

Router(config-subif)#en

Router(config-subif)#encapsulation d

Router(config-subif)#encapsulation dot1Q 40

Router(config-subif)#ip addr 40.40.40.1 255.255.255.0

Router(config-subif)#ex

Router(config)#ro

Router(config)#router ei

Router(config)#router eigrp 10

Router(config-router)#

Router(config-router)#net 34.34.34.0

Router(config-router)#net44.44.44.44.0

^

% Invalid input detected at '^' marker.

Router(config-router)#net44.44.44.0

^

% Invalid input detected at '^' marker.

Router(config-router)#net 44.44.44.0

Router(config-router)#net 30.30.30.0

Router(config-router)#net 40.40.40.0

Router(config-router)#ex

Router(config)#

Router#

%SYS-5-CONFIG_I: Configured from console by console

Router#rout

Router#hos

Router#host

Router#conf t

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#tou

Router(config)#hos

Router(config)#hostname IDN-R4

IDN-R4(config)#

Artikel Terkait

Superlab Cisco #1

4/ 5

Oleh Unknown

February 12, 2017 2 Komentar